Xenopixel V3 User Manual

Xenopixel V3 Lightsaber User Manual: A Complete Guide

The Xenopixel V3 lightsaber combines advanced technology, premium design, and stunning visuals to deliver an immersive experience for collectors, duelists, and Star Wars fans alike. This manual provides all the necessary details to safely operate, maintain, and fully enjoy your lightsaber. Follow the instructions carefully to unlock its full potential.

SAFETY GUIDELINES

LED Safety: Avoid staring directly into the LEDs to prevent potential eye strain or sight impairment.
Handle with Care: Some models may have sharp edges; use caution to avoid injury.
Do Not Dismantle: Avoid tampering with the internal electronics unless directed in the manual. Unauthorized modifications may void the warranty.
Protect from Water and Heat: Keep the lightsaber away from moisture and extreme temperatures to prevent damage.

GETTING STARTED

Unboxing and Setup

Carefully Unbox Your Lightsaber: Avoid using sharp tools to prevent accidental scratches or damage.
Inspect Components: Ensure all parts are included: hilt, blade, hex key, charging cable, and manual.
Blade Installation: Insert the pixel blade into the emitter, ensuring it makes full contact with the internal pins. Secure the blade using the provided retention screws and hex key. Avoid over-tightening to prevent damage.
Battery Installation: If required, insert the battery into the hilt’s compartment, aligning it with the correct polarity markings.

OPERATING YOUR LIGHTSABER

Basic Functions

Power On the Saber: Hold the power button for 2 seconds to activate the saber.
Ignite the Blade: Click the power button once to ignite the blade.
Turn Off the Saber: Hold the power button for 1.5 seconds to retract the blade.
Deep Sleep Mode: Hold the button for 10 seconds after turning off the saber to enter deep sleep mode, conserving battery life.

ADVANCED FEATURES

Blade OFF Functions

Volume Adjustment: Hold the button for 0.5 seconds. Release the button after the first flash to toggle between volume levels.
Light Effects: Hold the button for 1 second. Release after the second flash to cycle through different lighting effects.
Blade Modes: Hold the button for 1.5 seconds. Release after the third flash to toggle between blade modes (e.g., pulsing, stable, or unstable).
Font Selection:
- Rotate the hilt clockwise to select the next sound font.
- Rotate counterclockwise to return to the previous font.
Play Music: Point the hilt upward and twist counterclockwise, then clockwise to start or stop music playback.

Blade ON Functions

Blaster Deflect: Tap the power button to simulate deflecting blaster bolts.
Lockup Effect: Hold the button while tapping the blade against an object to create a lockup effect. Release to exit.
Drag Effect: Hold the button for 0.5 seconds and point the tip of the blade against a surface. Release to create a drag effect.
Melt Effect: Hold the button and press the blade tip against a surface to simulate melting. Twist the hilt to change melt colors.
Color Changing:
- Infinite Cycle Mode: Hold the button for 1 second to enter infinite color mode. Release and click to select your desired color.
- Twist Color Change: Hold the button and rotate the hilt clockwise or counterclockwise to cycle through colors.

CHARGING YOUR LIGHTSABER

Using the Charger: Connect the USB cable to the charging port on the hilt. Use a 5V/1A charger for best results.
Charging Indicator: A light on the chassis will illuminate during charging and turn off when fully charged.
Charging Duration: Avoid charging for more than 5 hours. Do not charge overnight to maintain battery health.
Battery Maintenance: Recharge the saber at least every two weeks to keep the battery in optimal condition.

Alternative Charging Method:

Remove the battery from the hilt and charge it using a compatible lithium battery charger. Ensure the charger matches the specifications of the battery for safe operation.

MOTION CONTROLS

Ignite/Deactivate Blade:
- Perform a quick stabbing motion to ignite or retract the blade.
Color Adjustment:
- Hold the button and twist the hilt clockwise to cycle through colors. Release the button to confirm.
Font Selection:
- Rotate the hilt downward and twist to switch between sound fonts.
Play Special Effects:
- Hold the button and twist the hilt upward to activate special effects such as force or melt actions.

UPDATING FIRMWARE

Access the Chassis: Unscrew the pommel and grip to expose the SD card and electronic board.
Remove the SD Card: Carefully slide the SD card out of its slot using your fingers or tweezers.
Download the Update File: Obtain the latest firmware file (e.g., update.bin) from your vendor.
Transfer the File: Insert the SD card into your computer, locate the set folder, and place the firmware file in the folder. Safely eject the SD card once complete.
Reinstall the SD Card: Insert the card back into the chassis, ensuring proper alignment. Reassemble the saber and restart it to apply the update.

TROUBLESHOOTING

Common Issues and Solutions

No Light from the Blade:
- Ensure the blade is properly installed and the retention screws are tightened.
- Recharge the battery if necessary.
No Sound Output:
- Adjust the volume settings.
- Confirm the saber is not muted or in sleep mode.
Blade Flickering or Dim Lighting:
- Recharge the battery or check the alignment of the blade with the emitter pins.
Charging Issues:
- Check the USB cable and charger for compatibility.
- Ensure the battery terminals are clean and properly connected.

CARING FOR YOUR LIGHTSABER

Clean the Blade: Wipe with a soft cloth to remove dust and debris. Avoid abrasive cleaners.
Maintain the Hilt: Use a dry cloth to clean the hilt and check for any loose components.
Storage Tips: Store in a cool, dry place away from direct sunlight or extreme temperatures.
Battery Safety: Follow proper disposal regulations for old batteries. Replace with compatible batteries only.

WARRANTY AND SUPPORT

Your Xenopixel V3 lightsaber is backed by a limited warranty covering defects in materials and workmanship. Warranty claims require proof of purchase and a detailed description of the issue. Contact customer support for assistance.

The anakin se saber is absolutely beautiful. The snv4 pro soundboard is unlike any saber i've ever used, this is my first "real" saber and i couldn't be happier. The store's communication was fantastic, quick to answer all my questions and even assisted with special ordering extra parts. The saber was on back order when i placed my order but it still arrived two days ahead of the estimated date provided by customer service. I think i've started an addiction and will almost definitely be buying more savers from this store. I think i need the ahsoka and obi-wan hilts now.

To say i was skeptical would be an understatement, but when it it arrived it not only showed up well packaged but also was exactly what they said it was.

I got the sn-pixel v4 pro, this is a neopixal blade unlike the others that are just hallow light up blades. I have plenty of video of it now, but doesn't really let me send video, so apologies for the picture only

the sword is nice I replaced the blade with a better quality and longer one. The bottom blade is quite flexible, it can completely resist heavy duels.
The sleeve is long and fits perfectly with 2 large hands. The sound is good but without more (6/10)

Fantastic product, very good price. The hilt looks and fees good too. It took a while to ship but i can’t complain too much given the great price.

Good quality. Thanks.

It arrived within a week of ordering.
The packaging was also sturdy and careful.
I would like to make another purchase if I have the opportunity.

Good repro light saber for the price. Blade is short, but the description shows this. I was expecting it to be short, and it will make a good prop for a cosplay when mobility is a factor.

For the price i paid im happy

The light saber came as described and is really awesome!! I am definitely going to buy more as gifts in the future from here because of how easy it was.

Totally awesome

It's great, I loved it

Exact outer diameter and inner diameter in a stylish material...good

Norm

Very cool. I accidentally hit my mom with it and now’s she’s dead.

Very pretty sword, of good quality, very fast shipping, I just regret that upon extinction, it does not keep the previously used modes in memory.

Seller that I recommend.

Works as stated in the item description. It's a shame there are no instruction manual in German.

thanks 😊 🫂 🙏

It arrived faster than I expected! The quality of it is so good! Highly recommended.

This was my first order from AliExpress, and specifically X-TREXSABER. The lightsaber came well packaged in a really cool case. It was simple to disassemble, charge, reassemble and then attach the blades. You have to be careful not to lose the screws as they are small, but they're easy to screw into place.

There are so many sounds, blade types and activation effects. I was blown away by the amount! I had to cycle through a few to get to Maul's sound effect, but the quality is so good and there's loads to choose from.

Super metal handle several colors. I recommend

item arrived and as described in the advertisement

Liked

Super ok